We could obtain a fee whenever you use our affiliate hyperlinks. However, this doesn’t impression our suggestions.
This slender desk maximizes minimal house.
My household just lately left our sprawling farmhouse for a compact ranch. We left our farmhouse-sized stuff too, and now we’d like new furnishings. This little console desk, underneath 4′ extensive and simply greater than 1′ deep, suits properly beneath a wall-mounted TV to maximise flooring house, and the detachable shelf gives useful cupboard space.
Stock Prep
Leg rip. Use a straightedge as a noticed information and rip 4 11⁄2″-square legs from the 2x6s.
Four 47″-long items make the highest and shelf. I purchased two 1x8s, which is simply sufficient however leaves little room for reducing off checks and cracks – take into account shopping for an extended piece (however 8′ is max for a lot of autos). You’ll additionally want two 6′ 1×6 boards for the facet, back and front aprons, in addition to two 6′-long 2x6s.
To make the legs, crosscut one 2×6 to 2 lengths of 311⁄4” on the miter noticed. Set a mix sq. at 11⁄2” and mark a line on the lengthy edge. Align your jigsaw blade (or round noticed blade) to your mark, then align and clamp a straightedge with the sting of the noticed’s shoe. Rip 4 legs.
When the legs are ripped to width, bundle them collectively to determine on and mark your last leg orientation.
Next, reduce two lengthy aprons from the 1×6 boards. Set a cease at 44″ on the miter noticed and chop each items to size. Cut the remaining 2×6 for the lengthy stretchers to that very same size.
Reset the cease to 111⁄2” and reduce two quick aprons from the remaining 1×6. Cut a 2×6 piece to the identical size for the quick stretchers.
To decide pocket-hole placement, measure and mark the middle and 3⁄4” in from each edges on the within of your apron faces. Drill three pocket holes on every finish.
Now drill a line of pocket holes alongside the highest inside edge of every apron: two on the quick aprons, three on the lengthy aprons. Ream the holes (wiggle the bit barely up and down in lengthy ones, facet to facet in brief ones) to permit for seasonal motion of the highest.
Rip the shelf stretchers to 11⁄4“.
Finish-sand every little thing to #180 grit. It’s simpler to do now than after meeting.
Assemble Aprons & Chamfer
Pocket energy. Carry marks as much as over the jig prime, then drill pockets at your apron ends.
Using a mix sq. set to 1⁄4“, mark a line, parallel to 3 edges, on either side of every of your 4 legs for chamfers (small bevels). Leave the within edges sq..
The aprons are inset 1⁄4” on the legs, aligned with the chamfers. The inset presents a problem in holding the aprons within the right place for meeting, however right here’s a easy resolution.
Start by assembling the tip items. Clamp a leg in your Workmate, leaving sufficient of it above the bench to safe F-style clamps to your workpieces.
Find a 1⁄4” thick scrap and reduce two lengths for “keys.” Put a scrap on every apron facet and clamp to the leg face.
Drive screws into the pocket holes to safe it to the leg, then screw the second leg to that meeting. Do the identical on the opposite finish meeting.
Grab your lengthy aprons (and a helper – this half will get somewhat difficult with simply two arms) and fix them to the tip assemblies.
Now chamfer the legs (you are able to do that earlier than meeting, but it surely makes clamping them in place tougher). Use a block airplane to chamfer to your 1⁄4” pencil marks. You could, like me, find yourself engaged on the ground for a couple of of those angles – limber up first. The block airplane received’t permit a full 1⁄4” chamfer close to the aprons, so chisel or sand to take away what the airplane can’t attain.
Contemporary Console Table Cut List
No.ItemDimensions (inches)Material
t w l
❏ 4 Top & shelf 3⁄Four x 7 1⁄Four x 47 Pine
❏ 2 Long aprons 3⁄4 x 5 1⁄2 x 44 Pine
❏ 2 Short aprons 3⁄Four x 5 1⁄2 x 11 1⁄2 Pine
❏ 4 Legs 1 1⁄2 x 1 1⁄2 x 31 1⁄4 Pine
❏ 2 Long stretchers 1 1⁄Four x 2 x 44Pine
❏ 2 Short stretchers 1 1⁄Four x 2 x 11 1⁄2 Pine
❏2Battens 1 x 1 x 11 Pine
Profile
Elevation
Stretchers & Top
Keyed up. Clamp 1⁄4″-thick scrap “keys” on both facet of the aprons as you safe them to the legs – these align the aprons with the structure for 1⁄4″ chamfers.
Determine your stretcher placement (I went with 10″ from the underside), and reduce a scrap piece to this measurement. Use this to put out your stretcher places on all 4 legs.
I secured the stretchers utilizing a pocket gap on every finish’s backside and inside edge. Remember to set your pocket-hole jig and bit for the correct thickness. Drill the holes, align the stretchers to your marks and safe them utilizing applicable screws (2″ for the within face, 21⁄2” for the underside).
Choose the best-looking 1×Eight for the highest and lay it lengthwise on the bottom. Flush one finish to a leg face, then mark the opposite finish. That’s the size of the highest and shelf. Set a cease to this measurement and reduce the 2 prime items. Secure them to the apron via the pocket holes you made earlier.
Now reduce the 2 shelf items to size, flush the ends and screw three scrap battens throughout the underside – one at every finish, one on the middle (ream these holes facet to facet too). Use a mix sq. to put out the sq. notches on the corners, then reduce them with a jigsaw. The shelf rests securely on the stretchers and is detachable.
I selected a gel stain (it blotches much less on pine) and topcoated with wipe-on polyurethane. Paint could look higher however, after years portray barns and fences, I actually needed to see the grain.
Download a free SketchUp mannequin for the “Contemporary Console Table.”
Product Recomendations
Here are some provides and instruments we discover important in our on a regular basis work across the store. We could obtain a fee from gross sales referred by our hyperlinks; nevertheless, we’ve got rigorously chosen these merchandise for his or her usefulness and high quality.
