We might obtain a fee if you use our affiliate hyperlinks. However, this doesn’t influence our suggestions.

26 drawers for instruments and provides.

My beat-up garage-sale seven-drawer metallic device cupboard was an eyesore. I wished one thing greater and higher, however principally I wished one thing that appeared prefer it belonged in a woodworking store. Online I discovered a picket model that match the invoice, however at $5,000 it was far too costly. After calculating that I may construct an even bigger and higher cupboard for lots much less, I made a decision it might be my subsequent challenge.

My cupboard stands barely greater than 5′ tall. The 9 small drawers on the high are side-hung. All the opposite drawers are mounted on full-extension slides. The slim drawer simply above the financial institution of side-by-side drawers is definitely a helpful pull-out shelf. The joinery is straightforward—pocket screws, biscuits, half-laps and rabbets—however the outcomes are rock-solid. You may simply reconfigure this cupboard to fit your wants. Replace a financial institution of drawers with doorways, for instance, or cut back the general measurement.

Ginormous Shop Cabinet Cut List

Overall Dimensions: 65-1/2″ H x 42-3/4″ W x 21-1/4″ D

Part

Name

Qty.

Material

Th x W x L

A

Cabinet facet

2

Oak plywood

3/4″ x 20″ x 64-3/4″

B

Horizontal divider

4

Oak plywood

3/4″ x 19-1/4″ x 39-3/4″

C

Top help

2

Oak plywood

3/4″ x 4″ x 39-3/4″

D

Side edgeband

2

Oak

3/4″ x 1/2″ x 64-3/4″

E

1″ edgeband

3

Oak

1/2″ x 1″ x 39-3/4″

F

3/4″ edgeband

2

Oak

3/4″ x 3/4″ x 39-3/4″

G

Back

1

Oak plywood

3/4″ x 39-3/4″ x 63-3/4″

H

Upper divider

2

Oak

1-1/2″ x 6-1/2″ x 20″ (a)

J

Upper divider edgeband

2

Oak

1/2″ x 1-1/2″ x 6-1/2″

Ok

Drawer help

18

Oak

3/8″ x 5/8″ x 15″

L

Lower  divider

1

Oak plywood

1-1/2″ x 20-7/8″ x 19-1/4″ (a)

M

Lower divider edgeband

1

Oak

1/2″ x 1-1/2″ x 20-5/8″

N

Corner block

4

Oak/Poplar

2″ x 2″ x 1-3/4″

P

Base trim entrance

1

Oak

3/4″ x 2-1/2″ x 42-3/4″

Q

Base trim return

2

Oak

3/4″ x 2-1/2″ x 20-1/2″

R

Top

1

Oak plywood

3/4″ x 20-1/2″ x 41-1/4″

S

Top edging entrance

1

Oak

3/4″ x 3/4″ x 42-3/4″ (b)

T

Top edging return

2

Oak

3/4″ x 3/4″ x 21-1/4″ [c]

U

2″ Drawer

9

Oak

2″ x 12-1/8″ x 15-1/2″

U1

Drawer entrance/again

18

Oak

3/4″ x 2″ x 12-1/8″ (d)

U2

Drawer facet

18

Oak

3/4″ x 2″ x 15″ (e)

U3

Bottom

9

Melamine

1/4″ x 11-1/8″ x 14-1/2″ (f)

V

3″ Drawer

4

Oak

3″ x 39-1/2″ x 18-3/4″

V1

Front

4

Oak

3/4″ x 3″ x 39-1/2″

V2

Box entrance/again

8

Birch plywood

3/4″ x 2-1/4″ x 38-3/4″ (g)

V3

Box facet

8

Birch plywood

3/4″ x 2-1/4″ x 17-1/2″ (h)

V4

Bottom

4

Melamine

1/2″ x 38″ x 17-1/4″ (j)

W

4″ Drawer

4

Oak

4″ x 39-1/2″ x 18-3/4″

W1

Front

4

Oak

3/4″ x 4″ x 39-1/2″

W2

Box entrance/again

8

Birch plywood

3/4″ x 3-1/4″ x 38-3/4″ (g)

W3

Box facet

8

Birch plywood

3/4″ x 3-1/4″ x 17-1/2″ (h)

W4

Bottom

4

Melamine

1/2″ x 38″ x 17-1/4″ (j)

X

Shelf

1

Oak

2″ x 39-1/2″ x 18-3/4″

X1

Front

1

Oak

3/4″ x 2″ x 39-1/2″

X2

Box entrance/again

2

Birch plywood

3/4″ x 1-13/16″ x 38-3/4″ (ok)

X3

Box facet

2

Birch plywood

3/4″ x 1-13/16″ x 17-1/2″ (l)

X4

Shelf

1

Melamine

1/2″ x 38″ x 17-1/4″ (m)

Y

5″ Drawer

8

Oak

5″ x 18-7/8″ x 18-3/4″

Y1

Front

8

Oak

3/4″ x 5″ x 18-7/8″

Y2

Box entrance/again

16

Birch plywood

3/4″ x 4-1/4″ x 18-1/8″ (g)

Y3

Box facet

16

Birch plywood

3/4″ x 4-1/4″ x 17-1/2″ (h)

Y4

Bottom

8

Melamine

1/2″ x 17-3/8″ x 17-1/4″ (j)

Z

Knob

9

Dull chrome

1-1/4″ dia.

ZZ

Pull

26

Dull chrome

3″ C–C

Notes:
a) Glue two 3/4″ items along with shims between to attain 1-1/2″ thickness.

b) Both ends mitered.

c) One finish mitered.

d) 1/2″ x 3/4″ rabbets on each ends; 1/4″ x 1/4″ rabbet for backside.

e) 5/16″ x 11/16″ groove for drawer information; 1/4″ x 1/4″ rabbet for backside.

f) 1/32″ x 1/4″ rabbet round high edge.

g) 1/2″ x 3/4″ rabbets on each ends; 3/8″ x 1/2″ rabbet for backside.

h) 3/8″ x 1/2″ rabbet for backside.

j) 1/32″ x 3/8″ rabbet round high edge.

ok) 1/2″ x 3/4″ rabbets on each ends; 3/8″ x 11/16″ rabbet for shelf.

l) 3/8″ x 11/16″ rabbet for shelf.

m) 1/32″ x 3/8″ rabbet round backside edge.

Fig. A) Exploded View

Fig. B) Side-Hung Drawers

Fig. C) Side View

Fig. D) Slide-Mounted Drawers

Fig. E) Pull-Out Shelf

Build the cupboard

1. Cut the edges, horizontal dividers and high helps (A–C, Fig. A, above) to remaining measurement after gluing on their edgebands (D–F). Note the totally different edge band widths.

2. Assemble the edges, dividers and helps with pocket screws, biscuits and glue (Fig. C). Temporarily set up the again (G) to maintain the meeting sq..

3. Glue collectively two items of plywood to create the higher dividers (H). Install shims between the items to match the 1-1/2″ width of the sting band (J). Glue on the sting bands. Then minimize the assemblies to remaining dimension.

4. Fasten drawer helps (Ok) to either side of the dividers and to the cupboard sides. Use 7/8″ and 1-1/2″ spacers to place the helps.

5. Install the higher dividers with screws and glue.

6. Glue collectively two items of plywood (with shims between) to create the decrease divider (L).

7. Install the decrease divider. Then glue on its edge band (M).

8. Install the nook blocks (N) and glue on base trim (P and Q).

9. Cut the highest (R) to remaining measurement and glue on its mitered edging (S and T).

Build the drawers

10. Cut all of the drawer field elements to measurement and rout rabbets on the ends of the fronts and backs (U1, V2–Y2 and Figs. B, D and E). The lowest full-width drawer (X) is definitely a shelf with a 3/16″ lip on the high to permit putting in a layer of cork.

11. Cut grooves within the sides of the two″ drawers (U2).

12. Glue and nail collectively the drawer packing containers. Then rout rabbets and set up the drawer bottoms (U3, V4, W4, Y4) and shelf (X4). Create efficient gluing surfaces on the melamine bottoms by routing shallow rabbets across the edges.

13. Test-fit the 9 side-hung drawers and make any vital changes. The fronts ought to cease flush with the cupboard, with 1/8″ gaps throughout. Make any vital changes and set up the pulls (Z, see Source, under).

14. Center and set up the drawer a part of every slide on the edges of all of the remaining drawer packing containers.

15. Install the cupboard a part of every slide within the cupboard (Fig. C).

16. Install the drawer packing containers and make any vital changes.

17. Cut the drawer fronts (V1–Y1) to remaining measurement and set up the pulls (ZZ, see Source).

18. Position the drawer fronts on the drawer packing containers. They prolong 3/8″ above and under the drawer packing containers, aside from the pull-out shelf entrance (X1), which is similar measurement because the shelf field. Use shims to create even spacing (1/8″ gaps throughout). Fasten the drawer fronts with 1/1-4″ #Eight flat head screws.

Final meeting

19. Fasten the again to the cupboard with screws.

20. Fasten the highest with screws by means of the highest helps.

21. For security, thread a big screw eye into the highest so you’ll be able to shackle the cupboard to the wall.

Sources

KVTT100 18″ Full Extension Side Mount Drawer Slide (13 pair req.)

Amerock Dull Chrome Wire Pull (26 req.)

Amerock Dull Chrome 1-1/4″ dia. Knob (9 req.)


Product Recommendations

Here are some provides and instruments we discover important in our on a regular basis work across the store. We might obtain a fee from gross sales referred by our hyperlinks; nevertheless, we’ve fastidiously chosen these merchandise for his or her usefulness and high quality.



Source link

LEAVE A REPLY

Please enter your comment!
Please enter your name here