We might obtain a fee while you use our affiliate hyperlinks. However, this doesn’t influence our suggestions.

Rarely a day goes by once we arent utilizing a router for some side of a challenge. Weve been constructing every kind of jigs and attempting new concepts (and concepts not too long ago unearthed from our archives). A router is really probably the most versatile instruments within the store, and we simply needed to share the following tips from the archives with you.

Router Jointer

You can use a router to joint two boards without delay. This is a extremely helpful trick should you don’t have a long-bed jointer otherwise you don’t have a jointer in any respect, and you’re working with actually lengthy inventory.

The trick is to rout each boards on the similar time, so the sides mirror one another. Bowed or not, they’ll at all times match tightly. To set this trick up, mill three spacer blocks to 1116” thick. Clamp the boards to a pair of sawhorses with the spacers between them.

Chuck a 34” bit in your router. Clamp the information board so the bit takes an equal quantity off each boards, about 132“. Ride the router tightly in opposition to the guideboard, eradicating the spacers as wanted. Any deviation or wandering from the router will probably be mirrored on the other board, offering an ideal match.

Offset Router Base

By merely including a customized, shop-made base to your router, you possibly can modify your minimize distance from the fence. A flip (or two, or three) of your router and youve set a brand new distance.

This sort of base, with completely different offsets, can be utilized for reducing dadoes and rabbets, in addition to stepped rabbets. You might additionally make one with 132” graduations for sneaking up on cuts and nice becoming dadoes.

Router Scarfing Jig

Boatbuilders usually want to hitch boards finish to finish to make longer planks. Instead of a butt joint they make an extended taper on every board and overlap the ends. This is known as a shawl joint. One or two scarf joints are simply planed by hand, however for any amount it’s properly value spending half an hour to make this easy jig.

The illustration exhibits 34” inventory being joined with a slope of eight to 1, which provides an overlap of 6″. Position the plank so the top to be joined is flush with the top of the jig and wedge it securely. Make one cross with the router utilizing a straight-flute plunge bit to take away the majority of fabric. Then reset the router for a second, lighter minimize, stopping simply in need of a feather edge on the plank finish. You might want to clear up the headscarf with a couple of passes of a low-angle block aircraft.

No-Fuss Mortising Jig

Want a dirt-simple mortising jig? This one takes just some minutes to place collectively, not the entire weekend. You will want a plunge router outfitted with an edge information.

First, clamp a 3″-  to 4″-square block to your bench. Fasten a 5″-long cease block to its aspect, close to one finish. Butt your workpiece as much as the cease block and clamp your workpiece to the big block. (A big handscrew is right for this job as a result of it has a deep attain.)

Lay out your mortise on the workpiece and modify the router’s edge information so the bit cuts throughout the structure marks. Finally, add two cease blocks on high of the large block to restrict the back-and-forth motion of your router. These blocks outline the mortise’s size. If your mortises are centered, go forward and minimize all of them. If they’re offset, merely change the fence setting as wanted.

Minimize Router Burns

End grain burns simply on maple and cherry, and these burns are arduous to take away. Here is a simple resolution that removes these ugly burns with out requiring that you just modify the bit’s peak or fuss with an edge information.

Before routing, three layers of masking tape on the underside of the board’s edge, the place the bit’s bearing rides. Then make two passes. The first cross produces the tough profile, when burning is more than likely to happen. After making the preliminary cross, take away the tape and rout once more. This very nice second cross removes all however the worst burns. If this methodology nonetheless leaves scorches, your feed charge is simply too gradual otherwise you want a brand new router bit.


Product Recommendations

Here are some provides and instruments we discover important in our on a regular basis work across the store. We might obtain a fee from gross sales referred by our hyperlinks; nevertheless, we’ve got rigorously chosen these merchandise for his or her usefulness and high quality.



Source link

LEAVE A REPLY

Please enter your comment!
Please enter your name here